Turret Sleeving International
Turret Sleeving International restores OEM tolerances to the upper turret stations on the Amada Turret Punch Press with our proven turret restoration process. TSI’s turret refurbishing experts will install hardened Steel Sleeves in the upper turret of your Amada punch press, which will restore the OEM specifications.
TSI has been solving turret accuracy problems for the past 25 years. We specialize in repairs for the Amada style turret punch press, including:
Any and All Amada Punch Presses.
Vipros, EM, EML, EMK EMZ, AE, Coma, Pega, Vela, Apelio, Aries and any King or Queen models.
Countries and growing
Each station getting sleeved is thoroughly cleaned, inspected and aligned before the Turret Restoration can begin.
The Turret Restoration process continues by using our State of the Art Boring equipment to bore out the damaged or worn stations.
After boring out the damaged stations or the complete turret the Sleeving process continues by cleaning all of the bored stations, getting it ready for the sleeves to be installed.
A TSI Hardened steel Turret Sleeve with an Amada OEM tolerance, Fully aligned and ready to punch.
We can help with your Auto index problems. We can simply replace the Auto-Index bushings or do a complete overhaul on both the upper and lower auto-indexes. We can also Resleeve any hard to find or overprized bushings.
The 6” or F size station is rare, but there is still a few machines left out there. We can install a hardened sleeve and replace the Die holder if needed, bring both back to OEM specifications.
Sleeving the Thin 2” and 3.5” or Thin C and D station is also a service that we can help you with.
We can retrofit our Turret Sleeves into both Thick or Thin style Octo-Racks as well as provide you with replacement Die Holder and Guide keys.
All Thin Turrets like Pega 244, Coma 255 or any Aries model can be retrofitted with our Turret Sleeves. We also carry Die holders and Guide keys for these models.
Replacement of X & Y axis Ball screws, Replacement of X & Y axis LM Guide Rails, Complete Clutch and Brake overhaul, Replacement of work holder clamps, Replace control with PC Control, All stations Sleeved with Turret Sleeves, New Guide keys, Springs, Bolts and Collars, All Die Holders replaced, Auto-index Stations Refurbished
If you want us to do the checking for you, we can arrange for one of our service technicians to come out to your facility and check the punch press for you, for just the cost of the travel. Or let us know where you are located and when we get close to your area, we’ll perform the check at no cost to you.
Turret Sleeving International, Inc., a Utah based company, has over 23 years experience refurbishing the upper turret stations of the Amada turret punch press. TSI has installed over 85,000 sleeves, world- wide and continues to grow.
Initially, the designers of the turret restoration process gained experience by working on Weidemann, Di-Acro, Behrens and Amada equipment, but recognized the growing need for Amada upper turret bore wear repair. Turret Restoration Inc., began specializing in the turret restoration of Amada Punch Press equipment exclusively.
Turret Sleeving International, Inc. has also become a distributor of quality replacement parts for your Amada Punch Press, such as the Retro Sleeve, auto-index guides, bottom die holders, guide keys, upper lifter springs and collars. TSI also offers a state-of-the-art, maintenance free, air-blow system, which can be retrofitted to your Amada Punch Press, and an Octo-rack exchange program.
TSI can usually schedule the refurbishing of your Amada Turret Punch Press within 30 days, with the downtime lasting only about 2 days. After the initial installation, your personnel may replace the Retro Sleeves if needed, once again restoring your punch press to OEM specifications. References from companies around the world are available.
MEET THE TEAM
James Shane Well
James Shane Well
We are committed to provide safe
industrial solutions to many factories